The Generosity™ Home Hydration System produces high quality alkaline water with a pH balance of 10.0. This unit takes your local water source and removes all dangerous impurities and add our Active Alkaline Technology. While most alkaline water uses inactive ingredients that lose their pH level over time, Generosity Water is engineered with natural active mineral ingredients that maintain a pH level of 10.0.

Our proprietary blend of Magnesium, Potassium, Sodium, and Ionic Calcium is ethically sourced from the ocean and allows our bodies receptors to retain active alkaline minerals directly into the blood steam. Transporting vital hydrating electrolytes to be absorbed by our bodies organs.

Tankless Under The Sink Design

The Generosity™ Home Hydration System’s compact and sleek filter system with a small and convenient footprint takes up less space and saves storage under kitchen sink! No tank also means no more secondary pollution. Guaranteed to provide ultra-pure, safe and clean water for you and your family.

600 GPD High Water Flow

The Generosity™ Home Hydration System’s can produce 600 gallons water per day. Its high capacity can serve the daily water needs of a large family. The water flow is fast and stable, the system can fill a 330ml cup of water in about 10 seconds.

1.5:1 Low Drain Ratio

Thanks to advanced water-saving technology, this system maximizes the efficiency and can save your water up to 450% compared with conventional RO filter systems on market! Being both economic and environmental friendly, it makes your water bills more affordable. Over the life of the system, The Generosity™ Home Hydration System pays for itself in water savings!

Smart LED Display & Quick Change

The smart display panel clearly tells real-time out TDS and remaining lifespan of each filter. The built-in TDS system constantly monitors the quality of your drinking water 24/7. Acting as a intelligent reminder, the color-coded indicators will always remind you to change filters in advance. With all parts included and well-organized instructions and videos, The Generosity™ Home Hydration System’s filter can be completely installed in a few minutes by yourself.

Model No.
G-600

Filter Cartridge Inside
ASR211, ASR212, TAM3

Product Dimensions
14.7 x 5.3 x 15.5 inches

Item Weight
33.06 lb

Working Pressure
Min.20psi Max.80psi

Flow Rate
0.41 GPM

Rated Voltage
110-240 VAC

Frequency
50-60 Hz

Rated Power
85 W

Operating Temperature
Min. 39 F, Max. 100 F

Q: Why there are many white bubbles in the water?

A: Normally for the first time use of the system, the water seems to have white bubbles in it, which is normal and totally drinkable. It is because when the pump is pressurizing the water, it will pressurize the air at the same time. It will make the air molecules smaller, thus the solubility further increases. The air can’t be released at that time because of the pressure in the system. However, when you turn on the tap to get a cup of water, the pressure of air is released. So you will see a huge number of bubbles in the water. It looks cloudy and white, but they are just bubbles. After you put the water still for a while, all bubbles will be gone, and the water is totally good for drinking.

Q: Why TDS is higher at the beginning, but back to normal range after about one minute?

A: Osmosis is a natural phenomenon happens in all RO system, no matter if you have a conventional RO system or tankless RO system. When the RO system starts to work, pressure from the pump overcomes natural osmotic pressure, forcing feed water through the RO membrane that removes the impurities. When the RO system stops working, the pump stops offering pressure as well. At that time, because of different concentrations, a small fraction of ions will enter into pure water and cause TDS to rise by a small amount. However, even if the TDS reading is a little high at the beginning, the quality water is still unbeatable by any other filtration methods including carbon, KDF, ceramic, UF, UV, etc.. The water is totally good to drink and you don’t have to wait for about 1 minute to get the water, since the whole system will not release any harmful substances to the water. The TDS removing rate for PD600-TAM3 is about 94-95%, if your incoming TDS is high, the outlet TDS will be high too.

Q: How does the TDS display on the machine work?

A: When the system is running, the TDS sensor in the PD600-TAM3 will keep testing the water quality every 1 minute. Therefore, the TDS result you see from the machine is from the last test memory. If you want to have the real-time TDS result, please let the machine run for about 1 minute.

Q: If I don’t want to use the TAM3, how should I disconnect it?

A: You don’t have to disconnect the tubing and the fittings on the TAM3. You only need to unscrew the TAM3 filter and the water still can go through.